// ...

IC-7600 User Manual in English is released. Here now at least you can read the new features summary

IC-7600 and keyb

User Manual in English version for the IC-7600 is released by Icom Inc. Jp.
Here now at least you can read the new features summary by www.radiocronache.com® —- (See the Link below for download User Manual)

Built-in a high-quality DSP-based Baudot RTTY modulator /demodulator and direct PC keyboard connection capability for RTTY and PSK operations without a PC. RTTY operation can be performed without an external RTTY terminal, TNC or PC. Pre-set characters can be sent using the RTTY memory. The contents of the RTTY memory/received signal can be saved into the USB-Memory. Two data formats, Text and HTML, are available for PC data storage.
Built-in a high-quality DSP-based PSK encoder /decoder is built-in to the IC-7600. When connecting a PC keyboard, BPSK (Binary Phase Shift Keying) and QPSK (Quadrature Phase Shift Keying) modes are available for PSK. The transmission contents can be typed before being transmitted. The contents of the PSK memory/received signal canbe saved into the USB-Memory.
[Note]: When a PC keyboard is connected to [USB] connector on the front panel, the RTTY/PSK/CW memory contentst nad the file name can also be edited from the keyboard. In this case, a USB hub is required.

PBT Operation

Twin PBT® operation: in SSB/CW/RTTY/PSK/AM the PBT (Passband Tuning) electronically narrows the IF passband width by shifting the IF frequency slightly outside of the IF filter passband to reject interference. The IC-7600 uses DSP for the PBT function. Moving both [TWIN-PBT] controls to the same position shifts the IF both above and below the received frequency.
DSP filter shape (Soft/Sharp): The type of DSP filter shape for each SSB, SSBD (data) and CW can be selected independently from soft and sharp. IC-7600 DSP use the TMS320C6726BRFP at 266MHz.
Roofing filter selection: The IC-7600 has 3, 6 and 15 kHz roofing filters at the 1st IF frequency. The roofing filter provides interference reduction from nearby strong signals.

LCD-display Large LCD with LED backlight multi-function Display. High resolution spectrum scope screen, several times to select the scope span: ±2.5, ±5.0, ±10, ±25, ±50, ±100 and ±250 kHz are available. This DSP-based spectrum scope allows you to display the frequency and relative signal strength  of received signals on the strengths of signals. The IC- 7600 has two modes for the spectrum display – one is center mode, and the other is fixed mode. In addition, the IC-7600 has a mini scope screen to save screen space.

Dualwatch operation. Dualwatch monitors 2 frequencies with the same mode simultaneously. During dualwatch, both frequencies should be on the same band, because the bandpass filter in the RF circuit is selected for the main readout frequency.

dualwatch

Push [MAIN/SUB] to enables the sub band access when changing the frequency to Main dial, etc. in sub band.
Adjust the [BAL] control to set a suitable audio signal strength balance between the main and sub readout frequencies. S-meter shows the combined signal strength. The dualwatch function is convenient for tuning the transmit frequency while monitoring both frequencies used for transmitting and receiving. Split frequency operation allows you to transmit and receive in the same mode on two different frequencies, on the main and sub readouts.

USB Rear connector. [USB] (Universal Serial Bus – B type) Connect a USB cable to be used for the modulation input, the transceiver operation with PC, the received audio and the decoded character import to the PC. Icom HP (http://www.icom.co.jp/world/support/index.html) gives the USB driver and the installation guide download service.
Sets the input modulation level of the [USB] connector from 0% to 100%  in 1% steps on the Level set mode. The received audio output level from [USB], cannot be adjusted with the [AF] control.

Link to: Download Icom Inc. Jp  User Manual English .pdf (14.87MB)

[Note] :
Please see te Icom official documents and data for more detail and totals feature
Icom, Icom Inc. are registered trademarks of Icom Incorporated  (Jp)

Commenti

Non sono abilitati commenti per questo post.

Comments are closed.

Articolo

Autore:
Link permanente
Categorie: IC-7600
Tag assegnati: , , ,

AD